CATALOGUES
•
•
•
•
•
•
SUSPENSION
•
•
•
•
•
•
•
•
•
•
•
COOLING PRODUCTS
•
•
•
•
•
•
CAR CARE
•
•
•
•
|
Suspension Bushes
| WHY SUPERPRO? |
INNOVATIVE DESIGNS AND FEATURES CREATE SOLUTIONS
FOR AUTOMOTIVE CHASSIS APPLICATIONS TO GIVE:
• Constant steering geometry • Better on road handling & control
• Longer service life of suspension components • Increased tyre life
• Extra off road stability • Alignment correction & stability.
• Traction control • More responsive steering
• MATERIAL:
SuperPro is a polyurethane elastomer uniquely blended to give an
extremely durable material with the best features of rubber and
plastic.
SuperPro is not affected by petrochemicals and it’s mechanical
properties creates the ideal material for automotive applications,
giving that “new car feel” for the remaining life of the vehicle.
SuperPro bushings remain constant in their durometer (hardness),
even under the most adverse conditions such as 4WD and off road
racing. |
|
 |
| ALIGNMENT CORRECTION: |
|
VOIDING: |
 Many front wheel drive vehicles do
not have provision for wheel
alignment correction and as the
vehicle’s suspension softens with
age, they begin to wander or steer
off in one direction.
Replacing with SuperPro bushes
rectifi es this by the removal of
excess compliance in the
suspension system without affecting
NVH (Noise Vibration and Harshness |
|
Allows polyurethane to be
dispatched into groves under
load, reducing NVH
(Noise Vehicle harshness).
|
| STEELWORK: |
|
THE DOUBLE HELIX: |
 SuperPro suspension components
use engineered crush tubes and
shells for longer life and to
eliminate slippage. The crush
tube is an integral component
of the suspension system and
allows for free pivoting. Careful
attention to hardness and design
gives a long service life. |
|
 The double helix is used on
specifi c applications. The
polyurethane material forms itself
into the grooves therefore
providing positive axial location
and still allows full rotation of
the pivot. It also acts as a grease
reservoir, which further increases
the service life of the bushings. |
| KNURLING: |
|
BULLET GROVES: |
 Knurling is used whenever
heavily laden bushings require
extra protection against adverse
wear. SuperPro’s special bore
knurling process, when
combined with our integral
grease retention lips keeps
lubricating grease intact for the
life of the bushing thus reducing
the necessity of re greasing. |
|
 SuperPro has developed a
method of achieving correct
pre-loads while still
accommodating a range of
variances in sizes. Bullet
grooves, tangential grease
groves & voiding allow the
bushings to fl ex and accept a
much wider range of sizes while
still maintaining free pivoting of
the bushings and reduce NVH. |
| BUMP STOPS: |
 |
|
SPF1832K:
Offers a universal fi tment for 4 & 6 Cyl lowered height vehicles with
a strut type suspension. The fi tment of lowered coil springs requires a
fi rmer shorten bump stop to control ride and allow suspension travel.
SPF1833K:
Offers a large universal fi tment range on all types of suspensions
where the bump stop works on a 10-14mm damper shaft. The bump
stop is designed so it can, be accurately trimmed to give the precise
amount of control with maximum travel.
SPF1833BK:
Offers a universal fi tment for 4, 6 & 8 Cyl lowered height vehicles with
a strut type suspension. The fi tment of lowered coil springs requires a
fi rmer shorter bump stop to control ride and allow suspension travel.
SPF2044K:
Offers a large universal fi tment range on all types of suspensions where
the bump stop works on a 14 - 18mm damper shaft. The bump stop is
designed to give the precise amount of control with maximum travel. |
| CLIP IN COIL SPRING SPACERS: |
 |
|
| PART # |
Qty |
Dimensions (mm) |
| SPF0352K |
3B |
A 26 |
| SPF0353K |
3B |
A 49 |
| SPF0438K |
3B |
A 25 |
|
| POLYURETHANE SOLID BAR: - (For Machining Custom Parts): |
 APPLICATION:
• All parts 300mm long
• Available in four different
hardness ratings 70, 80,
90 & 95
(70 being the softest)
Please quote required hardness
when
placing order. |
|
| PART # |
Dimensions (mm) |
| SPROD1-_ _ |
OD APPROX. 25 mm |
| SPROD1.5-_ _ |
OD APPROX. 38 mm |
| SPROD2-_ _ |
OD APPROX. 50 mm |
| SPROD2.5-_ _ |
OD APPROX. 63 mm |
| SPROD3-_ _ |
OD APPROX. 75 mm |
| SPROD4-_ _ |
OD APPROX. 98 mm |
|
| GREASE FOR BUSHES: |
 |
|
| PART # |
Dimensions (mm) |
| WPGREASE |
SUPER PRO (White) GREASE SACHETS |
| WPGREASEBULK |
SUPER PRO (100 White) GREASE SACHETS |
| WPGREASETUB |
SUPER PRO (White) GREASE 500g Tub |
|
|